EPOGLOSS-SL
Medium-High gloss, self-smoothing epoxy Aoor Top Coat
EPOGLOSS-SL
DESCRIPTION
EPOGLOSS-SL is a high gloss, self-smoothing, epoxy resin floor Anish applied between 1 - 3 mm thickness. It combines outstanding wearing properties with chemical resistance and decorative Anish. Ideally suited in situations where a seamless, joint free Anish is required and maximum cleanliness is essential.
USES
- Laboratories & clean rooms
- Pharmaceutical manufacturing
- Automotive manufacturing
- General medium to heavy industry
- Food and beverage production
- Warehouses and storage areas
- Printing plants
APPLICATION INSTRUCTIONS
Installation of EPOGLOSS-SL should be carried out only by an approved applicator of AIC
1. SURFACE PREPARATION.
Note: The substrate should have a surface tensile strength of at least 1.5 N/mm2.
The concrete substrate must be hard, sound, free of dust and other barrier materials such as paint, lime coatings, plaster, curing agents, laitance, oil, grease, wax, polish etc., that will inhibit adhesion to the substrate.
New concrete Aoors must be allowed to cure for at least 28 days and shall have an effective damp-proof membrane below to prevent rising dampness. Contaminated concrete surfaces should be mechanically prepared, by grinding, scariAcation, shot blasting or similar methods and be vacuum cleaned prior to installing EPOGUARD-SL Overwatered or otherwise weak concrete surfaces must be suitably prepared down to sound, solid concrete by mechanical methods. Dust and other debris should be removed using vacuum equipment.
Note: Any joints in the base e.g. movement joints, should be brought through to the Anished surface and suitably sealed.
PRIMING
All areas to be treated with EPOGLOSS-SL must Arst be primed with EPOPRIME-EP One or more coats of primer may be required depending upon the condition and porosity of the concrete substrate. High porosity substrates may be revealed after preparation and will be evident by their rapid suction and absorption. Poorly primed surfaces may lead to blistering or pin holing in the cured resin.
MIXING
The individual contents of EPOGLOSS-SL should be thoroughly stirred before being mixed together. Mix Part D with Part A and ensure smooth mixing. The entire contents should be poured in to a larger mixing vessel to incorporate Part B and Part C. The materials are mixed thoroughly with a spiral mixing paddle in a slow speed drill for 3 minutes until a consistent homogenous mix is achieved. One or more packs may be mixed simultaneously to ensure a quick rate of installation.
Note : Once mixed, the EPOGLOSS-SL will generate heat and lose working time if it is left in the mixing container or otherwise kept in bulk.
APPLICATION
The mixed EPOGLOSS-SL material should be applied to the prepared and primed surface without delay using a trowel or depth set rake to achieve the desired thickness. As soon as the EPOGLOSS-SL has been laid and as work progresses, the surface should be gently rolled with a spiked roller in order to release any entrapped air from the mix and also to blend out any trowel marks. The work area should be protected during the installation process and during the initial curing time to ensure that no debris can contaminate the surface, as this will lead to unwanted blemishes in the hardened, cured surface.
LIMITATIONS
The product should not be applied in temperatures less than 10°C or where the ambient relative humidity is greater than 85%.
MAINTENANCE
Good housekeeping and regular cleaning is essential in order to maintain the performance of EPOGLOSS-SL. It is particularly important in areas that are subject to regular spillage of chemicals. Spillages should not be allowed to dry, which results in higher concentrations of the chemicals, which may lead to early failure. Regular cleaning of the surface with a rotary scrubbing machine in conjunction with a water miscible cleaning agent or hot water washing at temperatures up to SOOC is recommended.
STORAGE AND SHELF LIFE
EPOGLOSS-SL has a shelf life of 12 months if kept in a dry, clean store between 5°C and 30°C in the original unopened containers. The product should be protected from frost, away from direct sunlight and sources of heat.
PRECAUTIONS
During mixing and application the following precautions should be observed: Ensure adequate ventilation and avoid contact of the material with the eyes, nasal passages, mouth and unprotected skin. Avoid contact with the hands by wearing protective gloves and by using, if necessary, a suitable barrier cream. In case of contact with the eyes, rinse immediately with plenty of water and seek medical advice and after contact with the skin wash immediately with plenty of soap and water. Prolonged contact with the skin should be avoided, especially where the user has an allergic reaction to resin-based materials. Always wear gloves and eye/face protection as necessary. Observe personal hygiene, particularly washing the hands after work has been completed or at any interruption whilst work is in progress. Care should be taken when removing gloves to avoid contaminating the insides. In case of accidents seek medical advice.
